HATO 400Y
A reliable drive for sliding gates for residential use, equipped with a magnetic encoder, which ensures maximum safety and precision of the actuator.
The gearbox of our flagship HATO 400Y actuator is made of bronze and steel.
Features of HATO 400Y:
- built-in control panel produced in Poland
- deceleration when starting and stopping the drive (soft START / STOP)
- radio receiver memory - 28 transmitters
- easy to unlock the drive in order to open the gate in the absence of power
- magnetic limit switches
- possibility of connecting photocells
- equipped with an encode
SLOW DOWN
a system that allows you to regulate the speed of the gate in the end positions. Thanks to this solution, the gate elements, such as fasteners, handles, toothed bars, toothed wheels or posts, extend their service life.
SEQUENTIAL SBS OUTPUT
Enables additional door control with devices such as: reset button (bell), mobile phone control, intercom control, rudder by means of a control panel or other external devices that are equipped with a low-current relay output can be integrated with the drive.
MAGNETIC LIMITERS
By eliminating the mechanical connection between the gate cams and the drive, we gain greater precision when setting the end positions, this solution eliminates the problem of snow remaining on the switch, which could have influenced the correct positioning of the gate. In practice, it speeds up the assembly of the entire control system.
EMERGENCY LOCKING
In case of a power loss, you can easily unlock the drive, which will allow you to open the gate. It is enough to disengage the drive (the flap in the lower part), insert the key provided with the set, then pull out the disassembly flap. Now we can manually open and close the gate.
SIGNAL RANGE
The set includes a remote control, the range of which is 25-35m depending on the type of fence, you can additionally increase the range of the signal thanks to the antenna built into the lamp included in the set. It is important that the extension is made with a 50 Ohm coaxial cable.
DRIVE POWER ADJUSTMENT
The drive is equipped with a potentiometer regulating the power of the drive, which allows for individual adjustment of the power to the weight of the gate.
FOOT TRAFFIC
The drive has two modes of opening the gate. The standard one opens the gate in 100% and the pedestrian mode opens the gate to a width of approx. 1 meter.
SECURITY
Slide 10/15 is equipped with an encoder, a device that checks the correctness of opening and closing the gate each time, in addition, the set includes photosensors that prevent the gate from closing when there is an obstacle in the gate's light. Another protection is the overload sensor, which will work when the gate senses resistance, before reaching the end position.
ROLLING CODE KEELOQ 433.92MHZ
Our company's remote controls are secured with a variable code in the "Keeloq" encryption system, which can only be logged into HATO drives, it is an additional protection against logging in by unsecured remote controls.
CE + declaration of conformity
- HATO confirms that the product meets the requirements of European Union directives.
Warranty
- 24 month.
• magnet + mounting - 2 pcs
• emergency key - 2 pcs
• mounting screw for the limit switch M6X18 - 4 pcs
• foundation bolt M10 - 4 pcs
• M10 nuts - 8 pcs
• flat washer Ø10 - 8 pcs
• spring washer Ø10 - 4 pcs
• photosensords
• LED warning light
• remote control x 2 pcs
• assembly instructions with a warranty card
HATO SLIDE 400Y drive specification:
Supply voltage
230 V AC/50 Hz
Engine power
160 W
The speed of movement of the gate
12 m/min
Maximum gate weight
600 kg
Remote control distance
≥ 30 m
Engine speed
1400 rpm
Output torque
10 Nm
Noise
≤ 60 dB
Control board
HEL B11
Remote control battery type
23 A (12 V)
Frequency
433.92 MHz with rolling code
Operating temperature
-40°C ~ +70°C
Dimensions
263 mm x 215 mm x 270 mm
HATO SLIDE 10
HATO 400Y
DOWNLOAD OUR CATALOG
